![]() Before reassembling, make sure the barrel and RSA are properly seated. Remove the slide, raise the slide lock and turn the take-down screw back to 90 degrees. The take-down screw or lever may not be at a 90-degree angle. To speed up the break-in, try racking the SAS slide 30–40 times without any ammunition or magazines. It can be fixed with a small slide barrel adjustment. Strip it down, clean it and use some lubrication. A new slide and the RSA being used may be a reason. Other times, it won’t return to batteries, but shooting should not be a problem. 5. Slide Issues:ĭuring reassembly, the slide won’t move all the way back and gets stuck. The sights are functional but not as bright as night sights with tritium inlays. The SAS’s Meprolight Bulleye sight is way off-center. They don’t function in all lighting situations. This will be more clear if you had a laser sight. In low light, the bullseye isn’t very noticeable. The guide rod and bolt threads at Rival Arms are most likely not primed. So, you’ll need to prime the threads for the thread locker to cure. Typically, these metals don’t activate the thread locker. The recoil spring retaining bolt and guide rod from Rival Arms are both made of steel with an oxide coating. Recoil springs made by ISMI undergo heat treatment, shot peening, and stress relief after forming to create a more durable and dependable spring.Īdditionally, because of the flat coil construction, there is very little chance of the spring coiling back on itself. This recoil spring also has a failure mode where it can coil back on itself and jam the P365 SAS after as few as 200 rounds. It is also not stress-relieved after forming. The spring that SIG uses is not heat treated. Moreover, spring rod failures are common causing the jamming of the gun. The recoil spring tends to get popped out of place. The JB Weld epoxy would stick perfectly to the stock Nylon layer. You can try extending the existing magazine release button. In that case get a longer magazine release button. But for people with long fingers, it is impossible. This could be solved by sliding the magazine release button to the opposite side of the grip module and using your index finger to activate the magazine release. In a defensive situation where you might drop the pistol while attempting a magazine change, this would be risky. If you didn’t twist the P365X in your grip, you couldn’t press the stock magazine release button. However, it doesn’t usually work with new SIGs. The recoil spring should be able to pull the slide closed. If it persists you can call SIG.Īnother solution is this: pull the slide slightly out of battery while the chamber is loaded. You can try leaving the gun fully loaded for a week. RTB failure is brought on by excessive friction from several sources. You may notice this with the mag fully loaded or even with one round less than full. These may be termed as ‘break-in’ issues. Bullseye Sight Issues Troubleshoot adjustment. ![]() Recoil Spring Rod Issues Troubleshoot or replace the spring rod. Magazine Release Button Issue Extend the release button. Quick Overview of the Problems and Solutions Problems Solutions RTB Issues Troubleshoot. ![]() Here are some of the issues and how to solve them. After shooting the P365SAS, sights will never look the same.The owners deal with many common SIG P365 SAS problems. The flush slide catch and takedown levers ensure absolute smoothness and zero snag risk. The ported barrel and slide results in up to 30% less muzzle flip and zero front sight fouling, since there isn’t one. With the assistance of fiber optics during the day and tritium in low light, the user can now obtain a crystal clear high-visibility bullseye sight picture at real-word engagement distances faster than ever before. With the incorporation of the FT Bullseye sight embedded into the slide, the P365SAS does away with the need of a primary snag hazard of all pistols…the front sight. This pistol does just that by taking the concept of the SIG Anti Snag (SAS) treatment to a whole new level. The P365SAS was designed for the serious CCW user who truly understands the value of smoother draws, faster sight acquisition, and more effective engagements at realistic distances. Here's what they have to say about the SIG P365 SAS: Lastly, the controls are shortened and flattened to maximize concealability. The second main difference about the SIG Sauer p365 SAS, one that may be a deal-breaker for some, is that the barrel is ported to help control muzzle rise.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |